[ays_quiz id="20"]
Free AMPP CIP Level II online practice exam quiz February 14, 2025March 17, 2025 Pass Guaranteed NACE CIP Level-1 Exam or get full refund guaranteed 10 Free AMPP CIP Level II online practice exam quiz 1 / 25 1) Which of the following is a requirement for preparing galvanized surfaces? They should be heated They must be allowed to weather They must be coated immediately They should be painted without cleaning 2 / 25 2) The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of Urethanes Inorganic zincs Epoxies Powder coatings 3 / 25 3) When observing fabrication defects, the NACE Inspector should: Require they be corrected prior to coating Consult the specification to determine how they should be treated Stop the job immediately Write an NCR and call the fabricator 4 / 25 4) What must be ensured before beginning waterjetting operations? The area is well-lit The work area is barricaded and safe The equipment is painted The operators are well-rested 5 / 25 5) What is the main focus of the Shipboard Corrosion Assessment Training (S-CAT)? Aesthetic evaluation Corrosion control knowledge Financial management Legal compliance 6 / 25 6) What type of paint should be used on galvanized surfaces? Any type of paint A wash primer or special tie coat Oil-based paint Water-based paint 7 / 25 7) What is the function of insulation half shells in pipeline applications? To enhance aesthetics To provide thermal insulation To reduce weight To prevent corrosion 8 / 25 8) What is a common failure mode in solvent-evaporation cured coatings? Excessive thickness Poor adhesion Incomplete curing All of the above 9 / 25 9) What is the typical temperature range for the sherardizing process? 100-200°C (212-392°F) 300-400°C (572-752°F) 500-600°C (932-1112°F) 700-800°C (1292-1472°F) 10 / 25 10) What is the main cause of solvent blistering in coatings? Poor ventilation during application Excessive DFT per coat Inadequate surface preparation All of the above 11 / 25 11) What is the main purpose of using sealers on thermal spray coatings? To enhance aesthetics To improve adhesion To prevent corrosion To increase thickness 12 / 25 12) Which of the following techniques is used in maintenance coating to ensure smooth transitions? Curling Feathering Layering Stacking 13 / 25 13) Which layer in hot-dip galvanizing contains 94% zinc? ZETA Delta Gamma ETA 14 / 25 14) What is the best practice if a pre-cure is performed during lining application? Continue with the final cure Repair and then complete the final cure Ignore the results of the pre-cure Document the findings only 15 / 25 15) What is a common requirement before applying any repair coating? Surface must be wet Must have a clean surface Surface must be painted Surface must be cold 16 / 25 16) What is the main advantage of using epoxy coatings on concrete? High flexibility Excellent adhesion and chemical resistance Low cost Easy application 17 / 25 17) What is the primary purpose of industry standards? To ensure aesthetic appeal To establish uniform criteria and practices To dictate product pricing To limit competition 18 / 25 18) Which layer in a three-layer polyethylene (3LPE) coating is applied directly to the steel substrate? Top layer Primer layer Fusion Bonded Epoxy layer Adhesive layer 19 / 25 19) You can use magnifiers to examine all of the following EXCEPT: Surface profile Surface cleanliness Blisters Mill scale 20 / 25 20) What factors can affect the time a surface retains its desired condition before coating? Ambient temperature Surface cleanliness Humidity levels All of the above 21 / 25 21) When using electrostatic spray equipment, what is essential for safety? Ensuring proper ventilation Grounding all conductive materials Wearing rubber gloves Ignoring static discharge concerns 22 / 25 22) When completing the Final Inspection report, the Inspector should write the report using: Language that only technical experts would understand Language that the most would understand Language that only those in the project would understand Language that another NACE Inspector would understand 23 / 25 23) The Concrete Repair Institute’s comparators can be used to assess: Surface cleanliness prior to coating Surface profile prior to coating Contamination levels prior to coating Compressive and tensile strength prior to coating 24 / 25 24) What is an important factor for the application of acrylic coatings? Low humidity High humidity Excessive heat Cold temperatures 25 / 25 25) Pre-cleaning of work pieces will NOT remove Snow, ice or water Oil or grease Dirt Mill scale Your score is LinkedIn Facebook Twitter VKontakte
